Oilfield equipment manufacturer · Dezhou, China
ZHUORUIOILFIELD EQUIPMENT
ASSEMBLE · SERVICE · VERIFY

Bucking unit

Zhuorui manufactures hydraulic bucking units for oilfield workshops that make up and break out threaded pipe and tool connections. The powered head rotates continuously while the backup head holds the other component. Match the gripping range, supports and torque-turn controls to the connections in your workshop.

10-24 inFrame sizes
360°Continuous rotation
0.5-6 rpmRotational speed
Continuous rotational headGripping matched to the workpieceTorque-turn monitoringBeckhoff PLC
18-month standard warrantyOn-site commissioning & training
Explore TorqueStar software
EQUIPMENT SPECIFICATIONS

Bucking unit specifications: grip, torque and speed

The reference frames run from 10 to 24 in. Start with the smallest and largest gripping diameters, then check the required torque and the length and weight of the assembly. The tables show which published ranges belong to each frame; the quotation confirms the supplied configuration.

Gripping diameter and torque by frame size

Select a size to add it to your enquiry.

Swipe the table to compare all columns →

FrameGrip · inGrip · mmTorque range · ft-lbTorque range · kN·m
10 in1⅝-1041.3-254500-130,0000.68-176
15 in2⅜-1560.3-3811,000-150,0001.36-203
18 in2⅜-1860.3-457.21,000-170,0001.36-230
20 in2⅜-2060.3-5081,000-199,0001.36-270
22 in2⅜-2260.3-558.81,000-199,0001.36-270
24 in2⅜-2460.3-609.61,000-199,0001.36-270

For these bucking unit frames, the published torque range is a single figure that does not separate make-up and break-out capacity. Confirm both duties for the selected machine. The frame labels identify sizes, rather than separate model codes.

Rotation, hydraulic supply and machine length

ItemReference specification
RotationContinuous 360°
Speed range0.5-6 rpm
Turn measurement increment0.0001 turn
Hydraulic pressure20 MPa normal / 30 MPa maximum
Maximum hydraulic flow250 L/min
Hydraulic tankUp to 500 L; confirm the supplied tank
PLC brandBeckhoff
Power supply380-480 V; three-phase, four-wire
Base skid length3,000-6,000 mm; configurable

The maximum pressure and flow figures are separate ratings. The turn increment describes the recording resolution; it is not a measurement-accuracy claim. We confirm the power supply, tooling and acceptance checks for the machine being supplied.

Specifications reviewed 16 September 2026.

The standard reference frames are 10-24 in. Made-to-order frames up to 32 in are available; their gripping range, torque and supports are specified separately.

SOFTWARE & JOINT RECORDS

TorqueStar torque-turn software

TorqueStar brings connection settings, live torque-turn monitoring and make-up reports into one workflow. Select the connection, follow make-up, then review the result.

Beckhoff PLC controls

Beckhoff PLC controls the machine; TorqueStar handles connection settings and job records. The quotation confirms the controller model, software functions and manual or automatic operating steps.

TorqueStar bucking unit software showing live torque, turns, clamp pressures and the torque-turn curve
Monitor torque and turnsSee live and peak torque, turns, clamp pressures and the torque-turn curve against the selected limits. The screenshot shows a run in progress.
Open monitoring screen ↗
TorqueStar connection library showing a VAM TOP specification, pipe dimensions and make-up torque limits
Built-in connection specification libraryVAM, TenarisHydril, JFE and TMK connection specifications.
  • Select by family, pipe size and grade; check weight, design and options.
  • View minimum, target and maximum make-up torque.
  • Where listed: shoulder, delta-turn and slope limits, plus clamping pressure.
Verify the selected entry against the connection manufacturer’s current data and procedure.
Open full-size image ↗
Bucking unit make-up report example with a torque-turn curve, connection details and recorded result
Review the recorded resultReview the curve, connection details and recorded result together. Keep the joint or tool ID, operator and job reference with the report.
Example from a separate make-up run.
Open full-size image ↗

Why we use Beckhoff control on our bucking unit

We choose Beckhoff for its PC-based platform, which can bring machine control, measurement and TorqueStar software together. That integration gives us flexibility to build the control and recording functions around your connection work.

How Beckhoff supports your connection work
Why we choose itWhat Beckhoff enablesWhat it means for your workshop
Control and software togetherMachine control and custom operator software can run on one compatible industrial PC.Connect TorqueStar’s connection selection, live curves and individual joint reports in one operating workflow.
Torque matched to turnsOptional measuring modules record when each reading was taken.Match torque to the corresponding turn to review where the load rises and the connection shoulder forms.
A configurable tightening sequenceTwinCAT can be programmed to control hydraulic valves, speed changes and stopping.Configure run-in, slower final tightening and stopping to suit the connection procedure, then verify them on the machine.
Room for additional requirementsModular sensor inputs and software connections support expansion.Plan for extra sensors or a connection to your production-reporting system when your work requires it.

Your quotation confirms the modules, software options and functions supplied. Whole-machine calibration and the pre-shipment factory acceptance test (FAT) verify the agreed measurement and control performance.

See a demonstration using your connection requirements →

PRE-SALES & AFTER-SALES SUPPORT

From order confirmation to after-sales support

Before you order: confirm the machine

We review your connections and workshop requirements, then confirm the drawings, functions, configuration and supply scope with you before ordering. Acceptance requirements and service arrangements are agreed at this stage.

ISO 9001:2015 certified quality management

Our quality management system is certified to GB/T 19001-2016 / ISO 9001:2015. Certificate No. CATC116824Q20054R0S was awarded to Dezhou Zhuorui Petroleum Machinery Co., Ltd by Shandong Chuangan Testing and Certification Group and is valid until 8 September 2027.

Its certified scope reads “Hydraulic disassembly frame, screw drill, screw drill machine test platform processing”: our hydraulic breakout frames, screw drills and screw drill test benches. You can check the certificate number on the CNCA website (www.cnca.gov.cn).

ISO 9001:2015 quality management system certificate No. CATC116824Q20054R0S awarded to Dezhou Zhuorui Petroleum Machinery Co., Ltd, valid until 8 September 2027
ISO 9001:2015 certificate, valid until 8 September 2027

Before shipment: witness the FAT

Once the machine is finished, we arrange a factory acceptance test (FAT) at our factory. You or your representative can attend, inspect the completed machine and test the agreed functions with our team before shipment.

The test follows the drawings, configuration and acceptance requirements confirmed before ordering.

Payment: T/T and L/C accepted

We accept T/T (bank transfer) and L/C (letter of credit). Advance payment depends on stock availability and the required configuration.

  • In stock and ready for immediate testing: no advance payment is required.
  • To be built or configured: advance-payment requirements and the payment schedule are agreed in the quotation.

The quotation confirms stock availability and when each payment is due.

After delivery: commissioning, training and support

  • 18-month standard warrantyExtended coverage up to 3 years by written agreement.
  • On-site commissioning & trainingAfter delivery, an engineer visits your workshop to commission the machine and train your operators.
  • Remote technical supportHelp with operation and troubleshooting. Share the machine ID and alarm details.
  • Spare-parts supportParts matched using your machine serial number and a part reference or photo.
  • Whole-machine torque calibrationCalibration of the complete machine using torque transmitters and supporting calibration equipment.
  • Middle East partner supportCalibration and after-sales support can be arranged through our regional partner. Tell us your machine model and location.
Bucking unit torque calibration assembly with flanged adapters, cables and a digital indicator
Our torque calibration equipmentTorque calibration assembly and digital indicator used for machine calibration.
View calibration equipment ↗
EQUIPMENT ENQUIRY

Get a bucking unit quote

Share your connection, tool dimensions or the job you need to do. You can leave detailed specifications for the follow-up.

Send your requirements directly to Zhuorui. Read our privacy notice.

THE EQUIPMENT

What is a bucking machine?

A hydraulic bucking unit, also called a pipe bucking machine, turns one part of a threaded connection while a backup head holds the other. Supports keep the assembly on the machine axis. Continuous rotation covers the initial thread run-in and the final make-up torque. The recording system plots torque against turns so the completed joint can be reviewed.

We supply configurations for casing, tubing, drill pipe, coupling buck-on (making up a coupling onto the pipe end) and downhole tools. For pipe make-up work, the combination of continuous rotation and a torque-turn record helps the workshop review each joint. If most of your work is dismantling service tools, compare the gripping and handling arrangements on our hydraulic breakout units.

Zhuorui is a bucking unit manufacturer in Dezhou, China. Established in 2011, the company carries out machining, hydraulic assembly and functional checks at its Pingyuan plant. Bucking units receive load testing, with torque-turn records supplied with the machine.

Bucking unit or breakout unit?

Both machines can make up and break out connections. Compare the drive, measured data and handling arrangement, rather than treating the names as opposite operations.

How the two connection machines differ
CompareContinuous-rotation bucking unitHydraulic breakout unit
Drive arrangementA powered head turns continuously through 360° under torque.High-torque wrenching and lower-torque thread spinning are separate functions.
Speed ratingReference operating speed: 0.5-6 rpm for controlled make-up.Spinner speed: up to 100 rpm. This is not the speed at maximum break-out torque.
Measured recordTorque against turns; shoulder and post-shoulder analysis with the specified package.Target and executed torque, a torque-time curve and a connection summary.
Typical workshop workCasing, tubing, coupling and connections requiring torque-turn acceptance.Mud motor and downhole-tool disassembly, repair and reassembly.
DESIGN & FUNCTION

Clamping, continuous rotation and torque-turn monitoring

Continuous rotation

The powered head can keep turning through the connection run-in. Depending on the controls supplied, the operator can use a faster initial rotation and a slower approach to final torque. The required speeds follow the connection procedure.

Jaws and gripping surfaces

Tell us where the jaws can contact the workpiece, the length available for gripping and whether jaw marks are acceptable. Those details determine the jaw profile, contact material and clamping arrangement. Tubulars with sensitive surfaces need a separate tooling check.

Torque-turn monitoring

The display shows the torque-turn curve as the joint is made up, together with the configured torque limits. Shoulder analysis is available where specified. The curve and shoulder information must be checked against the connection owner’s current acceptance procedure.

Supporting long or heavy assemblies

The bed, support jacks and extension beams can be arranged to suit the assembly. We also need to know how it will be lifted into place, which end enters the machine first and where the operator will work.

APPLICATIONS

Typical workshop uses

Casing, tubing and OCTG connection work

Oil country tubular goods (OCTG) work includes casing, tubing, couplings and pup joints. A bucking unit makes up their threaded connections and retains a record for each joint. The jaws must suit the actual gripping surfaces.

Premium connection assembly

Review torque-turn curves and the approach to the connection shoulder, using the connection owner’s limits and the monitoring functions specified for the machine.

Drill pipe and downhole-tool assembly

Assemble or separate drill pipe, BHA components and service tools that fall within the machine’s confirmed gripping, torque and support capacities.

WORKSHOP PROCESS

Planning a connection job

  1. 01

    Identify the connection

    Provide the thread type, component drawing and current make-up procedure. Include the torque limits and the information you need in the joint record.

  2. 02

    Choose the tooling and settings

    The jaws, supports and control settings need to match the job before the operator starts the approved cycle.

  3. 03

    Monitor make-up

    The display follows torque and turns during make-up. A machine supplied with automatic control uses the programmed settings as it approaches the target torque.

  4. 04

    Check the joint record

    Compare the recorded curve and final values with the connection criteria. Save the reviewed record with the joint identification and job reference.

This sequence explains the work to plan for. Operators must use the approved machine instructions and the procedure for the connection being assembled.

BEFORE YOU BUY

Match the bucking unit to your connections

Start with the work you need to complete. Send a list of representative connections or tool drawings, including the smallest, largest, shortest and heaviest items. We can then review the gripping, torque, supports and recording requirements together.

Information for a useful technical quotation
Your requirementWhat to share and confirm
Connections and workpiecesShare connection families, pipe sizes, weights, grades and drawings. Identify the jaw contact areas and any limits on surface marking. Confirm the gripping range and dies for those actual surfaces.
Torque dutiesState make-up and break-out torque separately, with units. Include the connection supplier’s procedure. Confirm both duties for the proposed configuration, including the lowest torque you need to measure.
Length, weight and handlingGive the longest and heaviest assembly, short pup joints and your loading method. Confirm bed length, support positions, lifting access and the room needed around the machine.
Controls and recordsSpecify manual or automatic operation and the records your customer requires. Review the Beckhoff PLC model, operator sequence, TorqueStar functions and a sample report against that requirement.
Workshop installationProvide the installation country, voltage, frequency and a floor plan. Confirm the electrical load, hydraulic equipment, foundation requirements and who supplies each site connection.
Order and support scopeBefore ordering, confirm the machine drawings, functions, configuration and itemized supply scope. Agree the after-delivery commissioning and training, calibration service, recommended spares and written warranty terms.
Software and reporting requirements

Send your connection families, sizes, weights and grades so we can confirm the required library entries and acceptance fields with the software package. Specify torque-turn measurement, shoulder detection, PDF reports and CSV sample data as needed. The SD example shown here includes a shoulder marker, turns after shoulder and slope data. Measurement functions depend on the supplied sensors and software; speed reduction and automatic stopping also require the matching machine controls.

For the workshop file, agree the joint or tool identifier, operator name and job reference in advance. Review the curve and the acceptance criteria with the result, then save the report for that connection.

Read the workshop records guide →

Agree what the factory acceptance test will demonstrate

We arrange the FAT at our factory on the finished machine before shipment. You or your representative can witness and participate in the test. Before ordering, choose representative connections and agree which functions and records the test must demonstrate.

  • Fit and handling: demonstrate the agreed gripping arrangement, workpiece supports and operating sequence.
  • Torque and recording: agree the verification method, measurement references, connection settings and report format.
  • Handover: list the operating and maintenance instructions, drawings, software backup arrangements and spare-parts references required with the machine.
Request a bucking unit quote
QUESTIONS & ANSWERS

Bucking unit questions

How does this differ from a breakout unit?

Both machines make up and break out threaded joints, and manufacturers use the names differently. On this site, the bucking unit page covers continuous rotation and torque-turn assessment. The breakout unit page compares DZZR main torque, spinner ratings and tool-handling options. Choose by the connections and service work you need to perform.

Does frame size determine torque capacity?

No. The opening size, jaws, drive and hydraulic system all affect the usable capacity. The quotation should state both the gripping range and the torque duties, so you can check that they cover the same workpiece.

What is needed to assess a premium connection?

The connection owner’s current procedure sets the acceptance criteria. The machine needs the specified measurements and correctly configured limits. Torque-turn and shoulder data help with the review, but a common control setting cannot approve every premium thread.

What do you need for a quotation?

Send the minimum and maximum gripping diameters, connection drawings, make-up and break-out torque requirements, and the longest and heaviest assemblies. Include the workshop power supply, layout and an example of the report you need.

How do manual and automatic bucking unit controls differ?

With manual lever controls, the operator controls machine motion and follows the displayed measurements. An automatic control package can manage programmed parts of the cycle, including the approach to target torque. Specify who controls clamping, rotation and stopping at each stage; recording torque does not by itself make a unit automatic.

Can one bucking machine handle casing, tubing and drill pipe?

It can cover different tubulars when the gripping range, jaws, torque capacity and supports suit each assembly. Check the smallest gripping diameter as well as the largest connection. Include pup joints and short components in the review, because available clamping length can limit the setup.

How do I get a price for a bucking machine?

The quotation depends on the frame and gripping range, required torque duties, bed length, jaw sets and control package. Handling equipment, reporting functions and delivery scope also affect the total. Send a tool list and connection drawings through the bucking unit enquiry form for a configuration-based quotation.

Do you manufacture bucking machines for sale?

Yes. Zhuorui manufactures new hydraulic bucking units for pipe and tool connection work. Send your gripping dimensions, make-up and break-out torque requirements, and the records you need. We can then quote the machine, tooling and support package for your workshop.

YOUR NEXT WORKSHOP PROJECT

Discuss a bucking unit for your connections

Send your gripping dimensions and torque requirements. We can review the frame size, tooling and recording options with you.

Send an enquiry

Last updated: · Markdown version: /products/bucking-units.md

Get a quote